This high viscosity, high build 100% solids epoxy is designed to cover minor imperfections in the concrete while providing a thick build and opaque finish.
E2000 is ideal for a solid color with a smooth finish. This product is easy to apply and has great self-leveling properties, making it perfect for almost any application.
100% high build and self-leveling for solid color floors
E 2000 100% solids high viscosity, high build epoxy is designed to cover minor imperfections in the concrete while providing a thick, smooth, and opaque finish.
E 2000 is ideal for solid color floors that require a smooth finish. This product is easy to apply and has great self leveling properties, making it perfect for almost any application.
SC 75 pre tinted single component is the recommended topcoat over E 2000. Anti skid additives can be added to the topcoat for traction.
Benefits and Features
- Foot traffic in 8-10 hours, 24 hour recoat window
- Easy to mix two A to one B ratio
- Ultra smooth and glossy finish when fully cured
- Excellent chemical and abrasion resistance
- Extreme adhesion to substrate
- Low temperature cure
- Zero VOC’s
- Pre tinted in multiple colors for easy installation
Uses and Applications
- Un even and pitted floors
- Automotive shops
- Garages floors
- Dog kennels
- Industrial shop floors
- Maintenance facilities
- Wastewater treatment facilities
- Anywhere a thick build, very smooth floor is desired
Product Physical Properties
Tensile Strength ASTM D412 3,750
Compressive Strength ASTM D695 13,400 psi
Impact Resistance ASTM D2794 225 lbs.
Flexibility (1/8 Mandrel) ASTM D2794 Pass
Fluxural Strength ASTM D790 12,500 PSI
Tabor Abrasion Mg Loss ASTM D4060 30
Product Cure Times
Tack Free Time @ 70 Degrees 6-8 Hours
Hard Dry 8-10 Hours
Foot Traffic 8-10 Hours
Re Coat 24 Hours
ASTMD 4541 Elcometer
Concrete Substrate Failure 450 PSI
Steel Delamination 600 PSI
Wood Substrate Failure 500 PSI
New concrete must have a 28 day cure and CSP 2-3, prior to coating. In the case of older concrete flooring, remove all surface oils, paint, dust and debris.
Prior to coating, make sure the surface is clean, and passes the MVT. Fix any needed repairs using CR Mender or CR Patch and Coat before application.
Recommended Coverage Rates
Coverage rates based on 1600 square feet per gallon at 1 mil in thickness.
Coverage rate will vary depending on application and substrate condition.
Shot blasted floors will require more product than ground floors.
1/8” notched squeegee and backrolled with 3/8” nap roller
-140-160 sq ft/ gal 10 Mils DFT
1/4” notched squeegee and backrolled with 3/8” nap roller
-100-125 sq ft/ gal 12 Mils DFT
Mixing Ratio Of 2 Parts A : 1 Part B
Always pre mix each side before use. Standard mix is 2 gallons of part A and 1 gallon part B. Mix with low speed drill for 3 minutes.
Pour entire batch of material on floor to keep product from cooking in bucket. Spread with squeegee or roller to desired thickness.
All containers should be stored at 40° F to 95° F and be kept tightly sealed and out of direct sunlight.
Shelf life of unopened containers is 12 months.
Available in 3 and 15 gallon kit. Available in 12 standard colors and clear. Product is pre-tinted for easy application and color uniformity.
PB 200 can be reduced with Xylene at no more than 15% of total mixed volume.
Chemical Resistant Chart
Acetic Acid 10% R Muriatic Acid 10% R
Acetone C NaCl/H2O 10% R
Benzene C Nitric Acid 20% NR
Brine saturated H2O R Phosphoric Acid 10 R
Chlorinated H2O R Phosphoric Acid 50 NR
Clorox(10%) H2O R Potassium Hydroxide 10% R
Diesel fuel C Potassium Hydroxide 20% R, Dis
Gasoline RC Skydrol RC
Hydrochloric Acid 20% R Sodium Hydroxide 25% R
Hydrofluoric Acid 10% NR Sodium Hypchlorite 10% R
Hydraulic fluid (oil) RC Sodium Bicarbonate R
Isopropyl Alcohol R Sulfuric Acid 10% R
Lactic Acid R Sulfuric Acid >50% RC
MEK NR Toluene C
Methanol R 1, 1,1-Trichlorethane R
Mineral Spirits RC Trisodium Phosphate R
Motor Oil R Vinegar/H2O 5% R
MTBE C Xylene RC
Chemical Resistance: Chart Key
R=recommended/little or no visible damage
RC=recommended conditional/some effect, swelling or discoloration
C=Conditional/Cracking-wash within one hour of spillage to avoid affects
All tools should be cleaned with MEK or Acetone as soon as possible after application.
- Mix Ratio 2A:1B
- Coverage 80-200 sq ft
- Cure Time 8-12 hrs.
- Pkg. Sizes 3 gal. kit, 15 gal. kit
- Blend Speed 1 speed