PB 200 Polyurea Basecoat/ Primer

PB 200 Polyurea Basecoat & Primer

Designed for broadcast systems

 

This 100% solids pure polyurea basecoat/primer is designed for broadcast systems; it’s a one-of-a-kind technology that offers extreme adhesion, rapid cure, and maximum broadcast time.

 

PB 200 is perfect for residential, commercial, and industrial use.

 

With excellent adhesion and extended pot life, this formula is useful for applications far beyond other polyurea or polyaspartics on the market today.

 

This 100% solids polyurea primer/basecoat is specifically designed for broadcast systems. It is a one of a kind technology that offers extreme adhesion, rapid cure and maximum broadcast time.

 

PB 200 is perfect for residential, commercial and industrial broadcast floors. With excellent adhesion and extended potlife, this formula is useful for applications far beyond other polyurea or polyaspartic technologies on the market today.

 

Benefits and Features

 

  • Foot traffic in 1-2 hours, 4-6 hour full return to service
  • Easy to mix two to one ratio
  • Extended potlife for ease of use
  • Maximum open time for broadcasting into
  • Extreme flexibility and elongation properties
  • Extreme adhesion to most substrates
  • Low temperature cure
  • Zero VOC’s
  • Pre tinted to ensure opaque basecoat

 

Uses and Applications

 

  • Garages floors
  • Basements
  • Automotive shops
  • Dog kennels
  • Parking decks
  • Bathrooms
  • Maintenance facilities
  • Sidewalks and walkways
  • Front entry ways
  • Showrooms

 

Packaging

 

Available in 3 speeds for all climate conditions. Summer, Winter, and X-treme Heat. Product comes pre-tinted in 2 standard colors, Grey and Tan.

 

Custom colors are available by request. Available in 3 and 15 gallon kits.

 

Product Physical Properties

 

Tensile Strength                       ASTM D412             6000
Elongation                               ASTM D412             129%
Compressive Strength               ASTM D695            9,400 psi
Tear Strength (PLI)                    ASTM D1737           350
Flexibility (1/8 Mandrel)             ASTM D2794           Pass
Falling Sand A Resistance          ASTM D968            30
Gloss                                       ASTM D523             90+
Tabor Abrasion Mg Loss             ASTM D4060          30

 

Product Cure Times

 

Tack Free Time @ 70 Degrees             40-75 Mins
Hard Dry                                           1-2 Hours
Foot Traffic                                        1-2 Hours
Re Coat                                             8 Hours

 

 

shop floor layers PB 200

Adhesion

 

ASTMD 4541 Elcometer
Concrete Substrate Failure                               550 PSI
Steel Delamination                                          1200 PSI
Wood Substrate Failure                                    500 PSI

 

Surface Preparation

 

New concrete must have a 28 day cure and CSP 2-3, prior to coating. In the case of older concrete flooring, remove all surface oils, paint, dust and debris.

 

Prior to coating, make sure the surface is clean, and passes the MVT. Fix any needed repairs using CR Mender or CR Patch and Coat before application.

 

Recommended Coverage Rates

 

Coverage rates based on 1600 square feet per gallon at 1 mil in thickness. Coverage rate will vary depending on application and substrate condition. Shot blasted floors will require more product than ground floors.

 

Roll application using 3/8” nap roller 275-325 sf/gal flat blade squeegee and backroll 250-275 sf/gal

 

Mixing Ratio Of 2 Part A : 1 Part B

 

Always pre mix each side before use. Standard mix is 2 qt
of part A and 1 qt part B. Mix with low speed drill for 2
minutes.

 

Do not whip product or induce air as it will
reduce pot life. Never mix more than 3 quarts at any time
and mix smaller batches for cutting in edges or verticals.

 

Apply with a brush, squeegee or 3/8” nap lint free roller.
Potlife will decrease with high humidity and high heat.

 

Reducers

 

PB 200 can be reduced with Acetone at no more than 20%
of total mixed volume.

 

Storage

 

All containers should be stored at 40° F to 95° F and be
kept tightly sealed and out of direct sunlight. Shelf life of
unopened containers is 12 months.

 

Clean Up

 

All tools should be cleaned with MEK or Acetone as soon
as possible after application.

Technicalread more

  • Mix Ratio 2A:1B
  • Coverage 200-300 sq ft
  • Cure Time 1-2 hrs.* 1-2 hrs.
  • Pkg. Sizes 3 gal. kit, 15 gal. kit
  • Blend Speed extreme heat, summer, winter

Downloadsread more

CONTACT US TODAY

Name*

Email*

Phone Number*

Address*

Message*

Become A Dealer

Developed by contractors, for contractors…we know what it’s like to walk in your shoes!

We understand the need to have an easy to use, reliable product that you can count on every day for consistent, quality results.  Penntek Industrial Coatings manufactures concrete coatings using the most advanced technology available to ensure contractors achieve successful installations every time.  Our award winning products and innovative formulations provide the highest standards in workability and performance.

Find Success by partnering with an industry leader in a growing industry!

Penntek’s goal is to develop long term partner relationships with companies that share our commitment to quality and service.  In addition to our industry leading products, we offer comprehensive training for installation, sales and marketing as well as on-going support.  Dealers of Penntek Coatings experience exceptionally high close rates and profitability from a product their clients love!